The 773 Series Cable Railing Kit by Ultra-Tec features a surface-mount to through-post configuration, along with two different cable size options and a wide variety of lengths, specifically designed for use with metal posts. It includes an Adjust-A-Body With Threaded Bolt fitting for screwing into one end post, and a Receiver with Push-Lock Stud for the other end post, making it the ideal solution for applications where both surface-mount and through-post installations are necessary. With this kit's 100% swageless design specifically made for DIY homeowners, it will completely eliminate the need for expensive professional installation while also making your deck look great!
Swageless fittings are made to be equipped with only the use of hand tools and can easily be installed by hand in the field, unlike traditional cable railings that require the use of a special swaging machine that crimps the fittings onto the cables. Additionally, swageless fittings can be removed and re-used for fixing or replacing the components or posts that the cable run goes through. By using swageless fittings, you eliminate the use of expensive installers and machinery because it can all be done with household tools in a matter of minutes.
Surface-Mount to Through-Post Configurations are the only types of installations that the 702 Series can be used with. Surface-Mount installations create an organized, clean look while also serving as a secure means of installing your cable railing in situations where the back of the post is inaccesible, while the Receiver is designed for through-post installations, almost completely concealing it inside of the end post.
- Swageless Design
- Metal Posts Only
- Level Runs Only
- Surface-Mount To Through-Post Configuration
- Cable Diameters: 1/8" or 3/16"
- Cable Lengths: 30', 40', 50' and 60'
- Stainless Steel Grade 316: Indoor/Outdoor Use
- 1x19 Stainless Steel Cable
- Adjust-A-Body With Threaded Bolt
- Receiver With Push-Lock Stud
- Delrin Washer For Metal
Metal Post Installations
For steel posts, a minimum size of 2" is required to keep the post from bending when cables are tensioned. Steel posts will need to have a minimum 1/4" wall in order to handle the hundreds of pounds of tension that is applied once the cables are tensioned. A top rail will also be needed in order to properly distribute the tension. For aluminum post installions, the end posts should be reinforced and it is recommended to use a bottom rail to prevent bowing. Both types of metal posts need to be securely mounted in order to prevent the post from coming loose while tensioning cables.
Intermediate posts (or mid-posts) are to be placed every 48" between end posts. An intermediate post runs from the top rail to the lower mounting surface and is integral for proper structural design. Intermediate posts can be substituted with something thinner such as an aluminum or steel cable brace. Cables are strung through holes in each post in order to provide support between end posts. Each post hole made should not exceed 3" vertical spacing in order to comply with IBC regulations. Cable Braces can be purchased here.
When taking cable railing through a corner, do not bend the cable past 45° at any time. If turning 90°, a 2-step turn using a double corner post configuration is required, as illustrated. For wood frame cable runs with up to 90° of turn, kits with single tensioners are sufficient. If going through corners totaling more than 90°, you will want to use a kit with tensioners at both ends.
Tools Needed For Installation:
- 5/32 Drill Bit For 1/8" Cable / 7/32 Drill Bit For 3/16" Cable
- 29/64 Drill Bit For Receiver Installation
- 3/16 Hex Wrench For Tensioning Receiver
- Cutting Tap Drill Bit I (For Pilot Hole) And 5/16-24 Tap For Adjust-A-Body With Threaded Bolt Installation
- 1/4 Wrench For Installing Threaded Bolt If Adjust-A-Body With Threaded Bolt
- 7/16 Wrench For Tensioning Adjust-A-Body
- 3/8 Wrench For Tightening Push-Lock Stud
- Cable Cutting Tool
*In order to comply with IBC regualtions, an intermediate post must be placed every 48" between posts and distance between each cable shall be no more than 3" clear span (for example if you are using 1/8" cable, you would space them 3-1/8" apart), however specific city and state rules and regulations may apply.
|Cable Kit Series||773|
|Post Type||Metal Post|
|Mount Type||Surface Mount to Through-Post|
|Cable Railing Design||Swageless|
|Kit Assembly Components||Adjust-A-Body With Threaded Bolt, Delrin Washer, Receiver With Push-Lock Stud|
|Cable Run||Straight (Level)|
|Cable Material||316 Grade 1x19 Stainless Steel|
|Environmental Impact||Made Of Recycled Materials|
|Country of Manufacture||United States|