We Are Open! Call 800.878.7829 or Order Online!

Ultra-Tec 262 Series Cable Railing Kit For Wood Posts (Level or Pitched Runs)

Ultra-Tec 262 Series Cable Railing Kit For Wood Posts (Level or Pitched Runs)
$32.66
Ultra-Tec 262 Series Cable Railing Kit For Wood Posts

* Required Fields

$32.66

Details

The 262 Series Cable Railing Kit by Ultra-Tec can be used for multiple different applications like stair-runs and level-runs with wood posts. It features two different cable options and a wide variety of lengths to satisfy the needs of almost any application. It is designed for through-post configurations using wood posts only. This kit features a tensioning device that is a pre-attached swaging stud which will attach to a 3½" long Invisiware Receiver,  installed through one of the end posts. A Pull-Lock fitting with cap is installed through the other end post. With this kit's 100% swageless design specifically made for DIY homeowners, it will completely eliminate the need for expensive professional installation while also making your railing look great!

Swageless fittings are made to be equipped with only the use of hand tools and can easily be installed by hand in the field, unlike traditional cable railings that require the use of a special swaging machine that crimps the fittings onto the cables. Additionally, swageless fittings can be removed and re-used for fixing or replacing the components or posts that the cable run goes through. By using swageless fittings, you eliminate the use of expensive installers and machinery because it can all be done with household tools in a matter of minutes.

Through-Post Configurations are the only mount type that the 262 Series may be used with. This is both the most cost-effective and least visible solution for installing cable runs. This means that each cable will start at one end post and continue through each intermediate post or cable brace until reaching the other end of its run. This configuration should be used when there are dedicated end posts for each run, and are situated so that the back side of the posts are all accessible.

Features:

  • Swageless Design
  • Wood Posts Only
  • For Level or Stair Runs
  • Through-Post Configuration
  • Cable Diameters: 1/8" or 3/16"
  • Cable Lengths: 5', 10', 15', 20', 25', 30', 40' and 50'
  • Stainless Steel Grade 316: Indoor/Outdoor Use

Includes:

  • 1x19 Stainless Steel Cable
  • Pre-Attached Swaging Stud
  • Pull-Lock Fitting With Cap
  • Invisiware Receiver
  • (2) Stainless Steel Washers

Wood Post Installations

For wooden post installations, a minimum size of 4" x 4" (3½" Sq.) is required to keep the post from bending when cables are tensioned. A top rail is also needed and recommended to be reinforced with a support such as a 2" x 4" on end under the top rail. End posts must also be securely mounted to the deck in order to prevent the post from coming loose while tensioning cables. A bottom rail is recommended for helping distribute the force away from the bottom of the post, however it is not required.

Pitched Installations

The cleanest approach to running cable on a pitch is to drill through both end posts on the square (NOT at the angle of the stairs). No beveled washers are necessary. Only intermediate posts need to be drilled on the angle of the stairs. This kit can be used to go up a stair and across a landing by inserting post protector tubes in the break-over point to prevent the tensioned cable from carving a groove into your wood post where it exits at an angle.

Intermediate Posts

Intermediate posts (or mid-posts) are to be placed every 48" between end posts. An intermediate post runs from the top rail to the lower mounting surface and is integral for proper structural design. Intermediate posts can be substituted with something thinner such as a 2" x 4" wood post, or an aluminum or steel cable brace. Cables are strung through holes in each post in order to provide support between end posts. Each post hole made should not exceed 3" vertical spacing in order to comply with IBC regulations. Cable Braces can be purchased here.

Corner Posts

When taking cable railing through a corner, do not bend the cable past 45° at any time. If turning 90°, a 2-step turn using a double corner post configuration is required, as illustrated. For wood frame cable runs with up to 90° of turn, kits with single tensioners are sufficient. If going through corners totaling more than 90°, you will want to use a kit with tensioners at both ends.

Corners require two posts because the cable itself, being rigid, will not cooperate in bending cleanly through a single post. When you go through a corner post, you will need to prevent the cable from slicing into the wood as it exits the post on an angle by using a post protector tube.

Tools Needed For Installation:

  • 5/32 Drill Bit For 1/8" Cable / 7/32 Drill Bit For 3/16" Cable
  • 29/64 Drill Bit For Invisiware And Pull-Lock Installation
  • 3/16 Hex Wrench For Tensioning Receiver
  • Cable Cutting Tool
  • 1/4 Drill Bit (If Using Post Protector Tubes)

Application Guide Level-Run Installation Stair-Run Installation

*In order to comply with IBC regualtions, an intermediate post must be placed every 48" between posts and distance between each cable shall be no more than 3" clear span (for example if you are using 1/8" cable, you would space them 3-1/8" apart), however specific city and state rules and regulations may apply.

 

Additional Information

SKU 262
Cable Kit Series 262
Post Type Wood Post
Mount Type Through-Post
Application Interior/Exterior
Cable Railing Design Swageless
Kit Assembly Components Invisiware Receiver, Pre-Attached Swaging Stud, Pull-Lock, Stainless Steel Cap, Stainless Steel Washer
Cable Run Pitched (Angled), Straight (Level), Straight or Pitched
Cable Material 316 Grade 1x19 Stainless Steel
Installation DIY Friendly
Environmental Impact Made Of Recycled Materials
Country of Manufacture United States
Manufacturer Ultra-Tec

Ultra-Tec 262 Series Cable Railing Kit For Wood Posts (Level or Pitched Runs)